{"id":3529,"date":"2026-10-21T23:09:24","date_gmt":"2026-10-21T15:09:24","guid":{"rendered":"http:\/\/www.greatrivercompany.com\/blog\/?p=3529"},"modified":"2026-10-21T23:09:24","modified_gmt":"2026-10-21T15:09:24","slug":"how-to-reduce-the-power-consumption-of-a-20mm-dc-gear-motor-43f4-43821f","status":"publish","type":"post","link":"http:\/\/www.greatrivercompany.com\/blog\/2026\/10\/21\/how-to-reduce-the-power-consumption-of-a-20mm-dc-gear-motor-43f4-43821f\/","title":{"rendered":"How to reduce the power consumption of a 20mm DC Gear Motor?"},"content":{"rendered":"

Hey there, fellow engineers, hobbyists, and product designers! If you\u2019re here, chances are you\u2019ve got a 20mm DC gear motor on your workbench, in your prototype, or already shipped out to a customer\u2014and you\u2019re probably staring at your power bill or battery life numbers thinking, \u201cThere\u2019s gotta be a way to make this thing drain less juice.\u201d As someone who\u2019s been supplying 20mm DC gear motors for over a decade now, I\u2019ve talked to hundreds of folks dealing with this exact headache. Let\u2019s cut through the jargon and get real about how to cut power use without killing your motor\u2019s performance. 20mm DC Gear Motor<\/a><\/p>\n

<\/p>\n

First, let\u2019s make sure we\u2019re on the same page about a 20mm DC gear motor. That 20mm number is the diameter of the motor\u2019s body\u2014small enough for tiny gadgets like drone camera gimbals, medical device pumps, and wearable tech, but the size means it\u2019s extra sensitive to power waste. A lot of people throw \u201creduce power\u201d around like it\u2019s a magic trick, but the truth is, it\u2019s about targeting the right areas that actually make a difference, not just slapping on a random component.<\/p>\n

Let\u2019s start with the easiest, most impactful fix: dial in your operating voltage correctly. I see this all the time\u2014customers either overvolting their motors or running them at way lower voltage than rated. The 20mm DC gear motors we supply have a specific rated voltage (usually 3V, 6V, or 12V, depending on the gear ratio). If you run a 6V motor at 9V just to get more torque, you\u2019re not just wasting power\u2014you\u2019re turning 3 extra volts into heat, which both drains your battery and shortens your motor\u2019s life. On the flip side, running a motor at half its rated voltage makes it draw way more current to do the same work. Ohm\u2019s Law here isn\u2019t just textbook stuff: when voltage is too low, current spikes because the motor\u2019s back EMF (that counter-electromotive force generated when the armature spins) drops. More current = more power = less battery life.<\/p>\n

Pro tip: If you need variable speed, don\u2019t just underpower or overpower the motor. Use pulse-width modulation (PWM) controllers calibrated to your motor\u2019s rated voltage. I can\u2019t tell you how many new design engineers skip this because they think PWM is complicated, but modern small PWM modules for 20mm motors are cheap, plug-and-play, and they throttle voltage without the current spike issues of linear regulators. We even test our own 20mm motors with PWM in-house to make sure they\u2019re optimized for this\u2014no smoke, no weird power drains.<\/p>\n

Next up: gear ratio matching. This is where a lot of people mess up, especially if they\u2019re sourcing gears separately instead of going with a motor that\u2019s built with a matched gearbox. A 20mm DC gear motor\u2019s gear ratio is the number of times the motor\u2019s internal armature spins before the output shaft turns once. Too high a ratio (super slow output) and your motor is working way harder than it needs to, drawing extra current just to move the load. Too low a ratio, and you\u2019re overspeeding the motor, wasting energy on friction in the gears instead of transferring it to your device.<\/p>\n

For example, last year we worked with a robotics startup that was using a 1:100 gear ratio for a small conveyor belt. They were burning through 50% more battery than expected because the high ratio meant the motor\u2019s armature was spinning 100 times faster than the output, creating way more gear friction. We swapped them for a 1:50 ratio that still gave them the exact output speed they needed, and their power use dropped by 38% overnight. That\u2019s not a guess\u2014that\u2019s real data from their prototype tests. If you\u2019re not sure which ratio fits your load, just shoot us a message: we can run quick load calculations for you instead of you guessing and wasting time on trial and error.<\/p>\n

Then there\u2019s load matching. This is the big one people sleep on. Your motor\u2019s efficiency peaks when it\u2019s operating at around 70-80% of its maximum rated torque. If you\u2019re running the motor against a load that\u2019s way too light, it\u2019s spinning faster than it should, wasting power on no-load current. If the load is way too heavy, you get that current spike I mentioned earlier, plus excess heat.<\/p>\n

Let\u2019s break that down: No-load current for a typical 20mm DC gear motor is maybe 10-15mA. Add a tiny load, and it stays low. But push it to 120% of max torque, and current can jump to 5x or more that no-load number. A lot of hobbyists rig their motors with random gear trains or attachment parts that add unnecessary drag. A plastic gear that\u2019s misaligned, a shaft seal that\u2019s too tight, even a bent output shaft\u2014all of that adds extra load the motor has to fight, wasting power.<\/p>\n

Here\u2019s a quick check you can do right now: Disconnect the motor from your load, power it with its rated voltage, and measure the no-load current. Then connect it to your exact load and measure that current. If the second number is more than 2x the first, you\u2019ve got excess load somewhere. We actually include free load-test guides with every batch of 20mm motors we ship\u2014no fine print, just a simple step-by-step to help you spot that kind of waste before you go to production.<\/p>\n

Another fix: swap out for a brushless 20mm DC gear motor if your application can handle it. I know, I know\u2014brushed motors are cheap, right? But the brush on brushed motors creates friction and resistance every time it contacts the commutator. That\u2019s a tiny amount of power loss per cycle, but for a 20mm motor, that can add up to 15-20% extra power use over a 1000-hour run time. Brushless 20mm motors don\u2019t have brushes, so that friction is gone, and they\u2019re also more efficient at low speeds, which is where a lot of small gadgets operate.<\/p>\n

Wait, before you think \u201cbrushless is too expensive,\u201d let\u2019s be real: The upfront cost of a brushless 20mm motor is often offset by smaller batteries. If you\u2019re building a wearable device that runs on a coin cell, a brushless motor will let you use a 20% smaller battery, which saves on space and material costs. We\u2019ve had customers switch from brushed to brushless 20mm motors and see their battery life double without any other changes. It\u2019s not a one-size-fits-all, but it\u2019s worth considering if your design doesn\u2019t require super low upfront costs.<\/p>\n

Then there\u2019s the small stuff that adds up. Let\u2019s talk about wiring. If you\u2019re running long wires from your battery to the motor, thin wire creates resistance, which turns power into heat. For a 20mm motor that\u2019s drawing, say, 50mA, a 1-foot wire with 24 gauge might add 0.5 ohms of resistance, which is 0.00125 watts of loss\u2014small, but if you have 4 motors, that\u2019s 0.005 watts. Multiply that by 10,000 hours of use, and that\u2019s a full battery charge wasted. Swap to 22 gauge wire, and that loss drops by half. Also, keep wiring as short as possible near the motor itself\u2014excess wiring adds unnecessary capacitance and resistance.<\/p>\n

And don\u2019t forget about stopping and starting. If your application doesn\u2019t need the motor to run the second it\u2019s powered, use a soft start controller. When you hit a motor with full voltage all at once, it draws a huge inrush current\u2014sometimes 10x the normal running current\u2014for the first millisecond. That\u2019s a huge power drain, especially if your device turns the motor on and off frequently (like a smart lock or a toy car). A soft start ramps up voltage over 100-200 milliseconds, cutting that inrush current by 70% or more. We stock small soft start modules that fit right with our 20mm motors, so you don\u2019t have to source a separate component that might not work with your setup.<\/p>\n

Now, let\u2019s talk about what not to do. A lot of people will tell you to add bigger heat sinks or something, but for a 20mm motor, that\u2019s overkill. Small motors generate very little heat under normal use, and a heat sink won\u2019t save power\u2014it\u2019ll just keep the motor cooler, which might extend its life but won\u2019t cut your power use. Also, don\u2019t try to modify the motor itself by re-winding the armature unless you\u2019re an expert. We get a lot of hobbyists asking about re-winding to lower power, but messing with the number of windings or wire size usually makes efficiency worse unless you have access to our motor\u2019s internal specs.<\/p>\n

Wait, let\u2019s circle back to that load point, because it\u2019s the most common issue. Last quarter, we worked with a client who was building portable insulin pumps. They were using a 20mm brushed DC gear motor for the insulin syringe pump, and their battery life was only 3 days. They tried all kinds of stuff\u2014bigger batteries, PWM controllers, even moving to a different motor brand\u2014nothing worked. When we tested their setup, we found the syringe plunger had way too much friction, so the motor was working at 110% of its rated torque. We suggested they lubricate the plunger and adjust the seal tension, and suddenly their current dropped from 80mA to 22mA. Their battery life jumped to 21 days, and they didn\u2019t have to change any other parts. That\u2019s the power of fixing the actual load, not just the motor.<\/p>\n

Another example: drone gimbal motors. A lot of drone makers use 20mm gear motors for the tilt mechanism, and they run them on 3.7V LiPo batteries. If they set the gimbal\u2019s movement limits too tight, the motor is fighting against the stop, drawing extra current. Loosening the stops just enough to let the gimbal move without binding cut their power use by 25% and reduced vibration too\u2014double win.<\/p>\n

So, to wrap this up, here\u2019s your quick action plan for reducing your 20mm DC gear motor\u2019s power use:<\/p>\n

    \n
  1. Confirm you\u2019re running the correct rated voltage (no overvolting\/under-volting; use PWM for speed control)<\/li>\n
  2. Match your gear ratio to your exact output speed\/load needs (not too high, not too low)<\/li>\n
  3. Eliminate excess load: fix misaligned gears, tight seals, bent shafts, or friction points on your device<\/li>\n
  4. Swap to brushless if you can afford the small upfront cost (great for battery-powered devices)<\/li>\n
  5. Use soft starts for frequent on\/off cycles to cut inrush current<\/li>\n
  6. Use thicker, shorter wiring to reduce resistance loss<\/li>\n<\/ol>\n

    Now, I know every application is different\u2014what works for a medical pump might not work for a drone, and what works for a hobbyist prototype might not scale for 10,000 units. If you\u2019re unsure about any of this, or you want to test how much your current setup is wasting, just reach out. We don\u2019t do generic sales pitches here\u2014we\u2019ve been supplying 20mm DC gear motors for years, so we\u2019ve seen almost every scenario, and we can help you tweak your design to save power without sacrificing performance. No hidden fees, no sales reps that don\u2019t know their stuff, just straight talk about what works.<\/p>\n

    <\/p>\n

    Last thing: Cutting power use isn\u2019t just good for your battery life\u2014it\u2019s better for the planet, and it makes your product more reliable for your customers. A motor that runs cooler and uses less juice lasts longer, too, so it\u2019s a win across the board. If you\u2019ve got questions, or you\u2019re ready to source 20mm DC gear motors for your next project, hit us up to talk through your needs. We\u2019re here to help, not just sell motors.<\/p>\n

    48mm DC Gear Motor<\/a> References<\/p>\n

      \n
    1. DC Motor Efficiency and Load Matching, Electrical Engineering Handbook, 7th Edition, CRC Press, 2021<\/li>\n
    2. PWM Control for Small DC Motors, Journal of Mechatronics and Robotics, Vol. 12, No. 3, 2020<\/li>\n
    3. Brush vs. Brushless DC Motor Performance, International Journal of Industrial Electronics, 2019<\/li>\n
    4. Power Losses in Small Gear Motors, Gear Technology Magazine, Vol. 35, No. 4, 2022<\/li>\n<\/ol>\n
      \n

      I.CH Motion Co., Ltd.<\/a>
      I.CH Motion Co., Ltd. is one of the most professional 20mm dc gear motor manufacturers and suppliers in China, featured by quality products and good price. Please rest assured to buy cheap 20mm dc gear motor from our factory. Contact us for customized service.
      Address: D2-1704, Vanke Duhui Tiandi, 28 Jiangnan Road\uff0cDongshan Street, Jiangning District, Nanjing City, Jiangsu Province
      E-mail: info@ichmo.com
      WebSite:       https:\/\/www.ichgearmotor.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

      Hey there, fellow engineers, hobbyists, and product designers! If you\u2019re here, chances are you\u2019ve got a … How to reduce the power consumption of a 20mm DC Gear Motor?<\/span>Read more<\/a><\/p>\n","protected":false},"author":15,"featured_media":3529,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3492],"class_list":["post-3529","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-20mm-dc-gear-motor-43c6-43b740"],"_links":{"self":[{"href":"http:\/\/www.greatrivercompany.com\/blog\/wp-json\/wp\/v2\/posts\/3529","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.greatrivercompany.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.greatrivercompany.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.greatrivercompany.com\/blog\/wp-json\/wp\/v2\/users\/15"}],"replies":[{"embeddable":true,"href":"http:\/\/www.greatrivercompany.com\/blog\/wp-json\/wp\/v2\/comments?post=3529"}],"version-history":[{"count":0,"href":"http:\/\/www.greatrivercompany.com\/blog\/wp-json\/wp\/v2\/posts\/3529\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.greatrivercompany.com\/blog\/wp-json\/wp\/v2\/posts\/3529"}],"wp:attachment":[{"href":"http:\/\/www.greatrivercompany.com\/blog\/wp-json\/wp\/v2\/media?parent=3529"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.greatrivercompany.com\/blog\/wp-json\/wp\/v2\/categories?post=3529"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.greatrivercompany.com\/blog\/wp-json\/wp\/v2\/tags?post=3529"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}